Making ATIS Accessible for Pilots who Are Deaf or Hard of Hearing
Anke M. Brock
1 a
, C
´
eline Classe
2
, Laura Duphil
1
, Florent Fabas
2
, Liam Guigo
1
, Thomas Holstein
2
,
Christophe Lounis
2 b
, Ilyes Reguig
1
and Caroline Senaux
1
1
ENAC, Universit
´
e Toulouse, Toulouse, France
2
SII, Toulouse, France
Keywords:
Aeronautics, General Aviation, Accessibility, Auditory Impairments.
Abstract:
Deaf and Hard of Hearing (DHH) pilots can easily fly in an uncontrolled space, where radio use is not required
to communicate with air traffic control. However, DHH pilots generally cannot fly without any assistance in
controlled airspace, where radio use is required. An important service for pilots in general aviation is ATIS
(Automatic Terminal Information Service), a vocal message containing essential information, such as weather
data, active runways, available approaches, and any other information needed by pilots. Pilots usually listen
to ATIS before contacting control, which reduces controller workload and decreases frequency occupancy.
However, since this is an audio-based service it is currently not accessible to DHH pilots. The FANS4all asso-
ciation (Future Air Navigation System for All) aims at making it possible for DHH pilots to fly in controlled
airspaces. In this paper, we present the user-centered design process of an accessible mobile ATIS application.
A resulting functional prototype has been evaluated in a pilot study with four pilots, including one DHH pilot.
1 INTRODUCTION
Deaf and Hard of Hearing (DHH) pilots can eas-
ily fly in an uncontrolled space, where radio use is
not required to communicate with air traffic control
(ATCO). However, DHH pilots generally cannot fly
without any assistance in controlled airspace, where
radio use is required. An important service for pi-
lots in general aviation is ATIS (Automatic Terminal
Information Service), a vocal message containing es-
sential information, such as weather data, active run-
ways, available approaches and any other information
needed by pilots. Pilots usually listen to ATIS before
contacting control, which reduces controller work-
load and decreases frequency occupancy. However,
since this is an audio-based service it is currently not
accessible to DHH pilots. D-ATIS (datalink) allows
transmitting written information, but it is currently
only used by large airports. As a result, alternative
communication methods between DHH pilots and air
traffic controllers have been developed. Current com-
munication methods that DHH pilots use are light gun
signals, a tool used by ATCO to communicate with
a
https://orcid.org/0000-0002-0017-396X
b
https://orcid.org/0000-0002-5804-6170
aircraft during communications malfunctions. These
lights emit different colored beams and can be flashed
or steady with different meanings for aircraft in flight
or on the ground. A second method depends on a
hearing copilot (radio copilot) onboard to communi-
cate with ATCO (Major et al., 2018) or listen to ATIS,
who then transmits the audio information to the fly-
ing pilot by writing on a whiteboard. These methods
are not always possible in the controlled airspace of
a large, crowded airport and thus present the primary
barrier for DHH pilots in pursing an Airline Transport
Pilot job or a non-commercial activity (Tinio, 2018).
The FANS4all association (Future Air Navigation
System for All, https://fans4all.org/) aims at making it
possible for DHH pilots to fly in controlled airspaces.
One challenge is the accessibility of ATIS for DHH
pilots. In this paper, we focus on the work conducted
to make ATIS more accessible on the side of the user
interface (i.e. the information presented to the DHH
pilot).
52
Brock, A., Classe, C., Duphil, L., Fabas, F., Guigo, L., Holstein, T., Lounis, C., Reguig, I. and Senaux, C.
Making ATIS Accessible for Pilots who Are Deaf or Hard of Hearing.
DOI: 10.5220/0011958300003622
In Proceedings of the 1st International Conference on Cognitive Aircraft Systems (ICCAS 2022), pages 52-56
ISBN: 978-989-758-657-6
Copyright
c
2023 by SCITEPRESS Science and Technology Publications, Lda. Under CC license (CC BY-NC-ND 4.0)
2 RELATED WORK
2.1 Technology to Support
Communication of DHH People
(Outside Aeronautics)
DHH people are largely excluded from communica-
tion with hearing peers. In the area of Assistive Tech-
nology, many researchers have investigated how to
support the communication of DHH users through
technology. Deaf people largely rely on the use of
sign language. One way to support this through tech-
nology is using sign language datasets (Bragg et al.,
2021). An alternative is the generation of sign lan-
guage avatars (Brock et al., 2020). Moreover, interac-
tive systems allow presenting environmental sounds
to DHH users through visual or tactile modalities of-
ten on mobile devices (Jain et al., 2020). For our work
we conclude that the tactile sens can easily be used for
alarms, but it is more convenient to provide detailed
information (such as names, or numbers) using the
visual modality as text or symbols. Moreover, mobile
and wearable solutions have proven to be interesting
for DHH users.
2.2 Making Aeronautics More Inclusive
In aeronautics, some studies have investigated the
possibility of using technology to allow sensory im-
paired people to fly (Val
´
ery et al., 2015). Blind pilots
currently use a sonification system, the sound-flyer,
which sonifies two dimensions of the aircraft attitude,
i.e. pitch and bank angles. The sound-flyer sonifi-
cation consists in modulating the features (i.e. fre-
quency, rhythm, inter-aural balance) of a sinusoidal
pure tone which is continuously displayed to the pilot
via his headphones (Val
´
ery et al., 2017). In contrast to
these technological advances for blind pilots, no sys-
tem is used for DHH pilots to the best of our knowl-
edge. A promising avenue is the implementation of
multimodal cockpit assistants (Lounis et al., 2019) or
mobile assistants (Simon et al., 2022) to support pi-
lots in difficult situations.
3 DESIGN PROCESS
To make ATIS accessible to DHH pilots, several as-
pects need to be addressed. In the current project, we
focus on the user interface, i.e. how to display the
information that is currently presented using audition
with a different sensory modality. To design a system
that meets the users’ needs, in our case DHH pilots
of General Aviation, we applied a user-centered de-
sign approach involving users at every stage of the
design process to ensure satisfying their needs. This
approach is in line with prior projects on mobile assis-
tants for General Aviation pilots (Simon et al., 2022).
Due to restrictions during the COVID crisis, we had
to adapt the process to comply with the local instruc-
tions and some steps had to be conducted online.
Since there are few DHH pilots in France (and none in
Toulouse) we extended our user population to hearing
pilots. 16 pilots (including 3 who were DHH) partic-
ipated in our project. Our design process consisted in
four different phases: exploration, ideation, elabora-
tion and evaluation.
3.1 Exploration Phase
The goal of the exploration phase is to better under-
stand the context and user needs. As a first step, a
workshop with DHH pilots and designers allowed to
better understand the current situation and problems
of DHH pilots. Following this workshop, the objec-
tive of the project was defined as designing and de-
veloping an accessible ATIS system that 1) delivers
the complete information currently delivered via ra-
dio / phone, 2) has a comparable or shorter acquisition
time as ATIS via radio / phone, 3) has a comparable
error rate as ATIS via radio / phone, 4) is usable dur-
ing all flight phases, 5) notifies pilots about changes
(update of ATIS) and 6) allows selecting a new airport
with a comparable or better time than ATIS via radio
/ phone. There was no constraint regarding the device
to be used. A second step consisted in an observa-
tion flight with two hearing pilots. Since the audio
quality of ATIS was bad, we concluded that a written
version of ATIS might even be of interest for hearing
pilots. Third, we conducted interviews with 14 pilots
(including one DHH pilot). This allowed us to pre-
pare 17 scenarios which involved the use of ATIS and
possible challenges, such as accessing the ATIS be-
fore the flight, accessing ATIS of an airport that was
not initially on the flight plan during the flight, equip-
ment malfunctioning, forgetting to consult ATIS be-
fore contacting ATCO, forgetting the frequency, etc.
3.2 Ideation Phase
The goal of the ideation phase is the creation of ideas
based on the observations from the exploration phase.
We conducted two brainstormings. First, an on-site
brainstorming with 10 students from ENAC who were
either studying to become pilots or aeronautical engi-
neers, and second an on-line brainstorming with one
Making ATIS Accessible for Pilots who Are Deaf or Hard of Hearing
53
Figure 1: Examples of sketches from the brainstorming session from left to right: 1) strip-based interface, 2) sketch of the
terrain, 3) mobile app interface.
DHH pilot and 6 pilot students. In both brainstorm-
ing sessions we asked the following two questions: 1)
How should ATIS information be visualized ? and
2) How should ATIS be selected ? At the end of the
on-site brainstorming session, we asked participants
to sketch ideas for an accessible ATIS system. Ideas
for different types of devices were proposed, such as
printing paper strips or using a mobile device (see
Figure 1 for examples).
3.3 Elaboration Phase
During the elaboration phase, we followed an iter-
ative design process, allowing us to converge from
initial paper-based prototypes to a functional proto-
type on an Android tablet. Initially, we explored de-
signs for four different device types: mobile phone,
tablet, smartwatch and an embedded cockpit system.
Videos of the prototypes were presented to ten users
online and asynchronously. We analyzed and priori-
tized the collected feedback. Based on this feedback
we made the following design decisions. First, we
decided to focus on the design of an application for a
tablet. Indeed, it presents the advantage over an em-
bedded system that no modifications to the cockpit are
required. Moreover, the display size is more adapted
for visualizing ATIS information than the smaller size
of phone or smartwatch. Finally, pilots are already
used to carry on tablets while flying (Simon et al.,
2022). Second, we learned that a radar view should
be included. Finally, we noticed that a few symbols
needed to be improved. Figure 2 shows the differ-
ent iterations of the mobile app interface. Prototype
1 was presented on-site to four pilots in a TB20 sim-
ulator and to two pilots in a wooden cockpit simu-
lator. Following the feedback from the users, mod-
ifications were made in Prototype 2 such as includ-
ing automatic update of ATIS and displaying the ver-
sion number through letters A,B,C,D etc. Prototype
2 (Adobe XD) was presented to six users online in
an experience map. This allowed to choose interac-
tion techniques such as the pie menu for the radar
view, a virtual keyboard with enlarged keys and ges-
ture recognition for the input of OACI code as well
as visual notifications. Prototype 3 (Adobe XD) was
presented online and asynchronous as videos to four
pilots (including one DHH pilot). Feedback was col-
lected through the use of a questionnaire. It allowed
us to identify modifications that were considered in
the final prototype for instance regarding choice of
colors and symbols. Prototype 4 was implemented in
React Native on Samsung Galaxy Tabs S6 Lite with
Android OS. It made use of the GPS position of the
tablet and touch recognition. ATIS update was han-
dled using HTTP communication. The interface was
slightly redefined based on the user feedback in previ-
ous steps, but also because of constraints due to mov-
ing from an Adobe XD prototype to an Android im-
plementation.
3.4 Pilot Study
We evaluated the prototype in a preliminary study
with four pilots, including one DHH pilot. All pi-
lots tested the application in a Flight Simulator with
Microsoft Flight Simulator 2020 and then replied to
a SUS questionnaire (Brooke, 1996). The three hear-
ing pilots and an additional fourth pilot participated
in a comparison between audio-based ATIS and our
mobile app. We also collected qualitative feedback.
DHH and hearing participants appreciated the appli-
cation and considered it useful. The SUS scores were
above 75 except for the first participant who encoun-
tered many technical problems during his test. Ac-
cording to (Bangor et al., 2008), SUS values above
75 correspond to a good, respectively excellent us-
ability. The comparison of audio-based ATIS and our
application showed that the mobile app was quicker
to use (mean gain of time: 13s). However, SUS and
time scores would need to be verified with a larger
ICCAS 2022 - International Conference on Cognitive Aircraft Systems
54
Figure 2: Iterations of the mobile app interface. Prototypes 2 to 4 are composed by two views: left: flight preparation, right:
ATIS consultation.
number of participants. Qualitative feedback allowed
us to identify aspects to further improve the applica-
tion in the future. For instance, some symbols need
to be improved to facilitate comprehension. More-
over, users requested to add direct interaction, such
as touching and moving elements or zooming with
pinch gestures. This is in line with interaction that is
already used in mainstream tablet applications. How-
ever, direct manipulation might be difficult during tur-
bulences and this would need to be studied further.
Pilots also appreciated that the mobile app included
features beyond ATIS (such as wind information and
a radar view). It inspired them to aim even larger for
a more holistic application that includes features be-
yond ATIS, similar as for instance FlyMate (Simon
et al., 2022).
4 DISCUSSION
This project is a first step towards a more accessi-
ble ATIS developed through a user-centered design
process with DHH and hearing pilots. However, the
current project only addresses the user interface and
some important challenges such as automatic speech
recognition from radio-based ATIS still need to be ad-
dressed. Since, there are currently few DHH pilots in
France (and none in Toulouse) this work has partially
been conducted with sighted pilots. Beyond involving
them as substitute users, we believe that an ATIS mo-
bile app might be interesting for them as well since
it allows including supplementary features and over-
coming low audio-quality of ATIS.
5 CONCLUSION AND FUTURE
WORK
In this paper we present the user-centered design, im-
plementation and preliminary evaluation of an acces-
sible tablet-based ATIS application. This project is
part of a bigger project, involving Fans4All associ-
ation, SII and researchers from Universities Rennes,
Tarbes and ENAC, and we will continue the work on
making piloting more accessible to DHH pilots. In the
future, it would be interesting to conduct a controlled
user-study with additional participants in a flight sim-
ulator or an aircraft. Moreover, it would be necessary
to work on the certification and regulations to make
this usable in the cockpit. We hope that this work
will inspire other researchers and designers to work
towards making aeronautics more accessible for peo-
ple with impairments.
ACKNOWLEDGEMENTS
First, we would like to thank all DHH and hearing
pilots who participated in the project. We are grate-
ful for the support by Fans4All association and SII.
This project was also conducted during the M2IHM in
Toulouse, and we would like to thank Sylvain Pauchet
and Nicolas Saporito for their helpful feedback.
REFERENCES
Bangor, A., Kortum, P., and Miller, J. (2008). An Em-
pirical Evaluation of the System Usability Scale. In-
ternational Journal of Human-Computer Interaction,
24(6):574–594.
Bragg, D., Caselli, N., Hochgesang, J. A., Huenerfauth,
M., Katz-Hernandez, L., Koller, O., Kushalnagar, R.,
Vogler, C., and Ladner, R. E. (2021). The fate land-
scape of sign language ai datasets: An interdisci-
plinary perspective. ACM Trans. Access. Comput.,
14(2).
Brock, H., Law, F., Nakadai, K., and Nagashima, Y. (2020).
Learning three-dimensional skeleton data from sign
language video. ACM Trans. Intell. Syst. Technol.,
11(3).
Brooke, J. (1996). SUS: A “quick and dirty” usability scale.
In Jordan, P. W., Thomas, B., Weerdmeester, B. A.,
and McClelland, I. L., editors, Usability Evaluation in
Industry, pages 189–194. Taylor & Francis, London,
UK.
Making ATIS Accessible for Pilots who Are Deaf or Hard of Hearing
55
Jain, D., Mack, K., Amrous, A., Wright, M., Goodman,
S., Findlater, L., and Froehlich, J. E. (2020). Home-
sound: An iterative field deployment of an in-home
sound awareness system for deaf or hard of hearing
users. In Proceedings of the 2020 CHI Conference
on Human Factors in Computing Systems, page 1–12,
New York, NY, USA. Association for Computing Ma-
chinery.
Lounis, C., Peysakhovich, V., and Causse, M. (2019). Flight
eye tracking assistant (feta): Proof of concept. In In-
ternational conference on applied human factors and
ergonomics, pages 739–751. Springer.
Major, W. L., Tinio, R. R., and Hubbard, S. M. (2018).
Able flight at purdue university: Case studies of flight
training strategies to accommodate student pilots with
disabilities. The Collegiate Aviation Review Interna-
tional, 36(2).
Simon, F., Imbert, J.-P., Cailleton, P., Hublet, L., and Brock,
A. (2022). Application mobile d’aide
`
a la navigation
a
´
erienne : une perspective de conception participative.
In 33rd Conference on Interaction Humain-Machine
(IHM ’22), Namur, Belgium.
Tinio, R. F. (2018). Perceiving the Communication Meth-
ods between Deaf Pilots and Air Traffic Control. PhD
thesis, Purdue University.
Val
´
ery, B., Peysakhovich, V., and Causse, M. (2015). Hear
me Flying! Does Visual Impairment Improve Au-
ditory Display Usability during a Simulated Flight?
Procedia Manufacturing, 3:5237–5244.
Val
´
ery, B., Scannella, S., Peysakhovich, V., Barone, P., and
Causse, M. (2017). Can an aircraft be piloted via soni-
fication with an acceptable attentional cost? a compar-
ison of blind and sighted pilots. Applied ergonomics,
62:227–236.
ICCAS 2022 - International Conference on Cognitive Aircraft Systems
56